Diaphragm waste evacuation pump. Rotates 360?. Run dry capable. Filterless design. Quiet running design. 1-1/2 ports, 5 GPM. 10 ft. self priming head, 12 Volt.

A right angle deck fitting nozzle for use with heavy-duty dockside pumpout 60500713. (Special order only).

For holding tanks and vacuum systems. Virtually unblockable and self priming up to 9.8 ft. Can be mounted in most convenient part of boat. Easy to maintain and can run dry without damage. Pumps inmacerated waste. Fuse size 15 amp automotive Output(open flow) 4-3/4 gallons per minute. Wire size of 16 AWG. Max head and lift is 9.8 ft. Hose connections are 1-1/2".

A high speed rotary cutter shreds waste more efficiently, allowing the impeller to rotate faster producing a higher discharge capacity. The brass shredder, nitrile impeller and stainless steel shaft prevents corrosion and is resistant to chemicals. Design allows for direct interchange with other macerators for easy installation. Empties a 30 gallon holding tank in about 3 minutes. Suitable for bowl or holding tank discharge. Self priming to 5 feet. Ignition protected. Capacity: 10.0 GPM. Voltage 12V DC. Amp draw: 15 max. Fuse size: 12 amp. Hose size: 1.5" intake.

A high speed rotary cutter shreds waste more efficiently, allowing the impeller to rotate faster producing a higher discharge capacity. The brass shredder, nitrile impeller and stainless steel shaft prevents corrosion and is resistant to chemicals. Design allows for direct interchange with other macerators for easy installation. Empties a 30 gallon holding tank in about 3 minutes. Suitable for bowl or holding tank discharge. Self priming to 5 feet. Ignition protected. Capacity: 10.0 GPM. Voltage 12V DC. Amp draw: 15 max. Fuse size: 12 amp. Hose size: 1.5" intake.

Effectively removes malodors emitted from tank vent. Comes complete with mounting bracket and hose adapters for 5/8" ID hose.

Effectively removes malodors emitted from tank vent. Comes complete with mounting bracket and hose adapters for 5/8" ID hose.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Manufactured of FDA approved polyethylene. All fittings are molded into tanks, eliminating stress cracking and leaking and are standard sizes. Easily adaptable for any boat. Has two 1-1/2" opening and one 1/2" vent.

Designed specifically for sanitation waste and fish box evacuations. Features run dry capability and seamless shell motor with o-ring sealed end bells and a sealed manual turn key. Dual blade and housing construction ensures problem free pumping. Thermally protected and ignition protected. Size: 10.79ö x 3.82ö x 4.48ö. Port size: inlet 1.5ö barb/1.5öNPT, outlet 1ö barb.

The Jabsco macerator pumps are the answer to holding tank pump outs. The macerator section grinds waste into small particles so it easily passes through the pump's hose discharge port. Detects the absence of fluid then shuts-off pump before impeller is damaged. Sensor provides a 16 - 20 second run-dry period to allow initial priming of pump. Interrupting power supply to the macerator resets the Run-Dry Device. Flow rate to 12 gpm (451pm). Self-priming to 4ft. (1.2m) vertical lift. Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection).

The Jabsco macerator pumps are the answer to holding tank pump outs. The macerator section grinds waste into small particles so it easily passes through the pump's hose discharge port. Detects the absence of fluid then shuts-off pump before impeller is damaged. Sensor provides a 16 - 20 second run-dry period to allow initial priming of pump. Interrupting power supply to the macerator resets the Run-Dry Device. Flow rate to 12 gpm (451pm). Self-priming to 4ft. (1.2m) vertical lift. Complies with USCG 183.410 and ISO 8846 MARINE (Ignition Protection).

The small cost answer to small boat waste retention. Lightweight. Rugged and compact. Easy to install. Constructed of tough polyethylene. Adaptable to all types of marine heads. Complies with USCG regulations calling for type III marine sanitary device. Includes mounting hardware. Inlet and outlet fit 1-1/2" hose. Vent is 3/4" hose.

For holding tanks and enables boatman to plug existing threaded fitting opening and to position new openings for fittings anywhere on tank. Comes with instructions.

For holding tanks and enables boatman to plug existing threaded fitting opening and to position new openings for fittings anywhere on tank. Comes with instructions.

For holding tanks and enables boatman to plug existing threaded fitting opening and to position new openings for fittings anywhere on tank. Comes with instructions.

Toilet waste pump is made of high quality ABS plastic. Lightweight. Can be mounted in various orientations/positions. Large non-choke valves. Tough plastic housing keeps in nasty smells. Easy to clean(no tools required) 14-3/4" gals per minute. 1-1/2" inlet/outlet. Max lift and max head of 15 ft. Service kit WHA AK8050.

Toilet waste pump is made of high quality ABS plastic. Lightweight. Can be mounted in various orientations/positions. Large non-choke valves. Tough plastic housing keeps in nasty smells. Easy to clean(no tools required) 14-3/4" gals per minute. 1-1/2" inlet/outlet. Max lift and max head of 15 ft. Service kit WHA AK8050.